In physics and engineering, surface power density, or sometimes simply specific power[1] is power per unit area.
Applications
The intensity of Electromagnetic radiation can be expressed in W/m2. An example of such a quantity is the solar constant.
Wind turbines are often compared using a specific power measuring watts per square meter of turbine disk area, which is \( \pi r^{2} \), where r is the length of a blade. This measure is also commonly used for solar panels, at least for typical applications.
Radiance is surface power density per unit of solid angle (steradians) in a specific direction. Spectral radiance is radiance per unit of frequency (Hertz) at a specific frequency.
Surface power densities of energy sources
Surface power density is an important factor in comparison of industrial energy sources.[2] Measured in W/m2 it describes the amount of power obtained per unit of area used by the specific energy source, including all supporting infrastructure, manufacturing, mining of fuel (if applicable) and decommissioning. Fossil fuels and nuclear power are characterized by high power density which means large power can be drawn from power plants occupying relatively small area. Renewable energy sources have power density at least three orders of magnitude smaller and for the same energy output they need to occupy accordingly larger area. The following table shows median surface power density of renewable and non-renewable energy sources.[3]
Energy source Median PD
| ergy source | Median PD
[W/m2] |
|---|---|
| Fossil gas | 482.10 |
| Nuclear power | 240.81 |
| Oil | 194.61 |
| Coal | 135.10 |
| Solar power | 6.63 |
| Geothermal | 2.24 |
| Wind power | 1.84 |
| Hydropower | 0.14 |
| Biomass | 0.08 |
Background
As an electromagnetic wave travels through space, energy is transferred from the source to other objects (receivers). The rate of this energy transfer depends on the strength of the EM field components. Simply put, the rate of energy transfer per unit area (power density) is the product of the electric field strength (E) times the magnetic field strength (H).[4]
Pd (Watts/meter2) = E × H (Volts/meter × Amperes/meter)
where
Pd = the power density,
E = the RMS electric field strength in volts per meter,
H = the RMS magnetic field strength in amperes per meter.[4]
The above equation yields units of W/m2 . In the USA the units of mW/cm2, are more often used when making surveys. One mW/cm2 is the same power density as 10 W/m2. The following equation can be used to obtain these units directly:[4]
Pd = 0.1 × E × H mW/cm2
The simplified relationships stated above apply at distances of about two or more wavelengths from the radiating source. This distance can be a far distance at low frequencies, and is called the far field. Here the ratio between E and H becomes a fixed constant (377 Ohms) and is called the characteristic impedance of free space. Under these conditions we can determine the power density by measuring only the E field component (or H field component, if you prefer) and calculating the power density from it.[4]
This fixed relationship is useful for measuring radio frequency or microwave (electromagnetic) fields. Since power is the rate of energy transfer, and the squares of E and H are proportional to power, E2 and H2 are proportional to the energy transfer rate and the energy absorption of a given material.[4]
Far field
The region extending farther than about 2 wavelengths away from the source is called the far field. As the source emits electromagnetic radiation of a given wavelength, the far-field electric component of the wave E, the far-field magnetic component H, and power density are related by the equations: E = H × 377 and Pd = E × H.
- Pd = H2 × 377 and Pd = E2 ÷ 377
- where Pd is the power density in watts per square meter (one W/m2 is equal to 0.1 mW/cm2),
- H2 = the square of the value of the magnetic field in amperes RMS squared per meter squared,
- E2 = the square of the value of the electric field in volts RMS squared per meter squared.[4]
References
Thompson, A.; Taylor, B. N. (2 July 2009). "Special Publication 811:Guide for the Use of the International System of Units (SI)". NIST.
"(PDF) Nature Energy and Society: A scientific study of the options facing civilisation today". ResearchGate. Retrieved 2020-07-23.
van Zalk, John; Behrens, Paul (2018-12-01). "The spatial extent of renewable and non-renewable power generation: A review and meta-analysis of power densities and their application in the U.S." Energy Policy. 123: 83–91. doi:10.1016/j.enpol.2018.08.023. ISSN 0301-4215.
OSHA, Cincinnati Technical Center (May 20, 1990). "Electromagnetic Radiation and How It Affects Your Instruments. Units" (Department of Labor - Public Domain content. Most of the content referenced by this work in this article is copied from a public domain document. In addition, this paper is a referenced work). U.S. Dept of Labor. Retrieved 2010-05-09.
Hellenica World - Scientific Library
Retrieved from "http://en.wikipedia.org/"
All text is available under the terms of the GNU Free Documentation License
