An optical waveguide is a physical structure that guides electromagnetic waves in the optical spectrum. Common types of optical waveguides include optical fiber and transparent dielectric waveguides made of plastic and glass.
Optical waveguides are used as components in integrated optical circuits or as the transmission medium in local and long haul optical communication systems.
Optical waveguides can be classified according to their geometry (planar, strip, or fiber waveguides), mode structure (single-mode, multi-mode), refractive index distribution (step or gradient index) and material (glass, polymer, semiconductor).
Dielectric slab waveguide
A dielectric slab waveguide consists of three dielectric layers with different refractive indices.
Practical rectangular-geometry optical waveguides are most easily understood as variants of a theoretical dielectric slab waveguide,[1] also called a planar waveguide.[2] The slab waveguide consists of three layers of materials with different dielectric constants, extending infinitely in the directions parallel to their interfaces.
Light may be confined in the middle layer by total internal reflection. This occurs only if the dielectric index of the middle layer is larger than that of the surrounding layers. In practice slab waveguides are not infinite in the direction parallel to the interface, but if the typical size of the interfaces is much much larger than the depth of the layer, the slab waveguide model will be an excellent approximation. Guided modes of a slab waveguide cannot be excited by light incident from the top or bottom interfaces. Light must be injected with a lens from the side into the middle layer. Alternatively a coupling element may be used to couple light into the waveguide, such as a grating coupler or prism coupler.
One model of guided modes is that of a plane wave reflected back and forth between the two interfaces of the middle layer, at an angle of incidence between the propagation direction of the light and the normal, or perpendicular direction, to the material interface is greater than the critical angle. The critical angle depends on the index of refraction of the materials, which may vary depending on the wavelength of the light. Such propagation will result in a guided mode only at a discrete set of angles where the reflected planewave does not destructively interfere with itself.
This structure confines electromagnetic waves only in one direction, and therefore it has little practical application. Structures that may be approximated as slab waveguides do, however, sometimes occur as incidental structures in other devices.
Waveguide are used in Augmented reality glasses, there are 2 technologies: diffractive waveguides and reflective waveguides.
Two-dimensional waveguides
See also: Planar transmission line § Imageline
Strip waveguides
A strip waveguide is basically a strip of the layer confined between cladding layers. The simplest case is a rectangular waveguide, which is formed when the guiding layer of the slab waveguide is restricted in both transverse directions rather than just one. Rectangular waveguides are used in integrated optical circuits and in laser diodes. They are commonly used as the basis of such optical components as Mach–Zehnder interferometers and wavelength division multiplexers. The cavities of laser diodes are frequently constructed as rectangular optical waveguides. Optical waveguides with rectangular geometry are produced by a variety of means, usually by a planar process.
The field distribution in a rectangular waveguide cannot be solved analytically, however approximate solution methods, such as Marcatili's method,[3] Extended Marcatili's method[4] and Kumar's method,[5] are known.
Rib waveguides
A rib waveguide is a waveguide in which the guiding layer basically consists of the slab with a strip (or several strips) superimposed onto it. Rib waveguides also provide confinement of the wave in two dimensions and near-unity confinement is possible in multi-layer rib structures. [6]
Segmented waveguides and photonic crystal waveguides
Optical waveguides typically maintain a constant cross-section along their direction of propagation. This is for example the case for strip and of rib waveguides. However, waveguides can also have periodic changes in their cross-section while still allowing lossless transmission of light via so-called Bloch modes. Such waveguides are referred to as segmented waveguides (with a 1D patterning along the direction of propagation[7]) or as photonic crystal waveguides (with a 2D or 3D patterning[8]).
Laser-inscribed waveguides
Optical waveguides find their most important application in photonics. Configuring the waveguides in 3D space provides integration between electronic components on a chip and optical fibers. Such waveguides may be designed for a single mode propagation of infrared light at telecommunication wavelengths, and configured to deliver optical signal between input and output locations with very low loss.
Optical waveguides formed in pure silica glass as a result of an accumulated self-focusing effect with 193 nm laser irradiation. Pictured using transmission microscopy with collimated illumination.
One of the methods for constructing such waveguides utilizes photorefractive effect in transparent materials. An increase in the refractive index of a material may be induced by nonlinear absorption of pulsed laser light. In order to maximize the increase of the refractive index, a very short (typically femtosecond) laser pulses are used, and focused with a high NA microscope objective. By translating the focal spot through a bulk transparent material the waveguides can be directly written.[9] A variation of this method uses a low NA microscope objective and translates the focal spot along the beam axis. This improves the overlap between the focused laser beam and the photorefractive material, thus reducing power needed from the laser.[10]
When transparent material is exposed to an unfocused laser beam of sufficient brightness to initiate photorefractive effect, the waveguides may start forming on their own as a result of an accumulated self-focusing.[11] The formation of such waveguides leads to a breakup of the laser beam. Continued exposure results in a buildup of the refractive index towards the centerline of each waveguide, and collapse of the mode field diameter of the propagating light. Such waveguides remain permanently in the glass and can be photographed off-line (see the picture on the right).
Light pipes
Main article: light tube
Light pipes are tubes or cylinders of solid material used to guide light a short distance. In electronics, plastic light pipes are used to guide light from LEDs on a circuit board to the user interface surface. In buildings, light pipes are used to transfer illumination from outside the building to where it is needed inside.
Optical fiber
The propagation of light through a multi-mode optical fiber.
Main article: Optical fiber
Optical fiber is typically a circular cross-section dielectric waveguide consisting of a dielectric material surrounded by another dielectric material with a lower refractive index. Optical fibers are most commonly made from silica glass, however other glass materials are used for certain applications and plastic optical fiber can be used for short-distance applications.
See also
ARROW waveguide
Cutoff wavelength
Dielectric constant
Digital planar holography
Electromagnetic radiation
Erbium-doped waveguide amplifier
Equilibrium mode distribution
Leaky mode[12]
Lightguide display
Transmission medium
Waveguide
Waveguide (electromagnetism)
Photonic crystal fiber
Photonic crystal
Prism coupler
Zero-mode waveguide
References
Ramo, Simon, John R. Whinnery, and Theodore van Duzer, Fields and Waves in Communications Electronics, 2 ed., John Wiley and Sons, New York, 1984.
"Silicon Photonics", by Graham T. Reed, Andrew P. Knights
Marcatili, E. A. J. (1969). "Dielectric rectangular waveguide and directional coupler for integrated optics". Bell Syst. Tech. J. 48 (7): 2071–2102. doi:10.1002/j.1538-7305.1969.tb01166.x.
Westerveld, W. J., Leinders, S. M., van Dongen, K. W. A., Urbach, H. P. and Yousefi, M (2012). "Extension of Marcatili's Analytical Approach for Rectangular Silicon Optical Waveguides". Journal of Lightwave Technology. 30 (14): 2388–2401. arXiv:1504.02963. Bibcode:2012JLwT...30.2388W. doi:10.1109/JLT.2012.2199464.
Kumar, A., K. Thyagarajan and A. K. Ghatak. (1983). "Analysis of rectangular-core dielectric waveguides—An accurate perturbation approach". Opt. Lett. 8 (1): 63–65. Bibcode:1983OptL....8...63K. doi:10.1364/ol.8.000063.
Talukdar, Tahmid H.; Allen, Gabriel D.; Kravchenko, Ivan; Ryckman, Judson D. (2019-08-05). "Single-mode porous silicon waveguide interferometers with unity confinement factors for ultra-sensitive surface adlayer sensing". Optics Express. 27 (16): 22485–22498. doi:10.1364/OE.27.022485. ISSN 1094-4087.
M. Hochberg; T. Baehr-Jones; C. Walker; J. Witzens; C. Gunn; A. Scherer (2005). "Segmented Waveguides in Thin Silicon-on-Insulator" (PDF). Journal of the Optical Society of America B. 22 (7): 1493–1497. Bibcode:2005JOSAB..22.1493H. doi:10.1364/JOSAB.22.001493.
S. Y. Lin; E. Chow; S. G. Johnson; J. D. Joannopoulos (2000). "Demonstration of highly efficient waveguiding in a photonic crystal slab at the 1.5-μm wavelength" (PDF). Optics Letters. 25 (17): 1297–1299. Bibcode:2000OptL...25.1297L. doi:10.1364/ol.25.001297.
Meany, Thomas (2014). "Optical Manufacturing: Femtosecond-laser direct-written waveguides produce quantum circuits in glass". Laser Focus World. 50 (7).
Streltsov, AM; Borrelli, NF (1 January 2001). "Fabrication and analysis of a directional coupler written in glass by nanojoule femtosecond laser pulses". Optics Letters. 26 (1): 42–3. Bibcode:2001OptL...26...42S. doi:10.1364/OL.26.000042. PMID 18033501.
Khrapko, Rostislav; Lai, Changyi; Casey, Julie; Wood, William A.; Borrelli, Nicholas F. (15 December 2014). "Accumulated self-focusing of ultraviolet light in silica glass". Applied Physics Letters. 105 (24): 244110. Bibcode:2014ApPhL.105x4110K. doi:10.1063/1.4904098.
Liu, Hsuan-Hao; Chang, Hung-Chun (2013). "Leaky Surface Plasmon Polariton Modes at an Interface Between Metal and Uniaxially Anisotropic Materials". IEEE Photonics Journal. 5 (6): 4800806. Bibcode:2013IPhoJ...500806L. doi:10.1109/JPHOT.2013.2288298.
External links
AdvR – Rubidium doped waveguides in potassium titanyl phosphate (KTP)
Hellenica World - Scientific Library
Retrieved from "http://en.wikipedia.org/"
All text is available under the terms of the GNU Free Documentation License
